Testers
The standards require that voltage testers, which load the measuring point with an operating current higher than AC 3.5mA and DC 10mA either have to be equipped with a push button on each test probe to activate the measurement or with a protective cap in order to protect the contact electrodes against accidental contact.
Product safety is ensured by:
- Vibrating alarm for safe voltage detection
- Load connection via two membrane push buttons
- Continuity check via buzzer and LED or LCD respectively
Filter by Producers - See all
Technical Data
|
Voltage and Continuity Tester |
|||||||
|
|
DUSPOL digital LC |
DUSPOL analog plus |
DUSPOL expert |
DUSPOL master |
DUSPOL combi |
DUSPOL compact |
PROFIPOL |
|
indication |
LED/LCD |
plunger systenVLED |
LED/LCD |
LED/LCD |
LED/LCD |
LED |
LED |
|
indication steps |
6 - 750 V |
12-690 V |
12-690 V |
12-690 V |
12-690 V |
12-690 V |
6 - 400 V |
|
continuity test |
buzzer + LCD 200 kQ |
- |
buzzer + LED 108 kQ |
- |
LCD 600 kQ |
- |
- |
|
phase-sequence test |
yes/LCD |
yes/LCD |
yes/LCD |
yes/LCD |
- |
- |
- |
|
single-pole phase test |
yes/LCD |
yes/LCD |
yes/LCD |
yes/LCD |
yes/LCD |
- |
- |
|
polarity test |
yes/LCD |
yes/LED |
yes/LED |
yes/LED |
yes/LED |
yes/LED |
yes/LED |
|
load connection via push buttons |
ls = 200 mA (750 VDC) |
ls = 250 mA (750 VDC) |
ls = 200 mA (750 VDC) |
ls = 200 mA (750 VDC) |
ls = 200 mA (750 VDC) |
ls = 200 mA (750 VDC) |
- |
|
30 mA Fl triggering via push button |
yes |
yes |
yes |
yes |
yes |
yes |
- |
|
vibrating alarm |
yes |
yes |
yes |
yes |
yes |
- |
- |
|
measuring point illumination |
yes/LED |
- |
yes/LED |
- |
- |
- |
- |
|
protection class |
IP 64 |
IP 64 |
IP 64 |
IP 64 |
IP 64 |
IP 64 |
IP 65 |
|
item no. |
50258 |
50257 |
50253 |
50252 |
50254 |
50251 |
20022 |
Catalogs and Technical Documents
Products
| Item No | Description | Producer |
| 044111_Benning | Light sensor Luxmeter type B for tester IT120 B, Benning, 044111 | Benning GmbH |
| Benning_ IT110 | Tester Benning IT 110 for insulation with Utest=100/250V/500V/1000V, Ik.s. =24.4kA, DTZ check, voltage up to 500V, circuit, 044100 | Benning GmbH |
| Benning_ IT120 | Tester Benning IT 120 B for insulation with Utest=100/250V/500V/1000V, Ik.s. =24.4kA, DTZ check, voltage up to 500V, ground loop resistance 0.01-2000 Ohm, 0.1mA-20 A, USB,RS-232, software, 044102 | Benning GmbH |
| Benning_020054_VT1 | Tester VT1, 200-1000V, non-contact phase and phase sequence indicator, CAT IV 600 V, CAT III 1000 V, IEC/EN 61010-1, Benning 020054 | Benning GmbH |
| Benning_044055_VT2 | Tester VT2, 12-1000V, non-contact phase and phase sequence indicator, CAT IV 600 V, CAT III 1000 V, IEC/EN 61010-1, Benning 044055 | Benning GmbH |
| Benning_10162173 | Switchable test probe 4mm for BENNING IT 105/IT 101, Benning, 10162173 | Benning GmbH |
| BENNING_IT105 | Tester Benning IT 105 for insulation with Utest=250V/500V/1000V, resistance with Itest=200mA, voltage up to 440V, circuit, 044105 | Benning GmbH |
| Benning_IT115 | Benning IT 115 Insulation Tester with Utest=100/250V/500V/1000V, Line Impedance and Circuit Test, 044104 | Benning GmbH |
| Benning_IT130 | Tester Benning IT 130 for insulation with Utest=50/100/250V/500V/1000V, checking DTZ, voltage up to 500V, resistance to ground loop 0.01 ohm-2 Kohm, 0.1 mA-400 A, 0.01 lux-20 klux , USB, RS 232, software, 044103 | Benning GmbH |
| BENNING_SDT1 | Tester SDT1 for contacts and DTZ U=230V AC, active PE test, LED, 30mA, Benning 020053 | Benning GmbH |
| Benning_ST725 | Mobile tester ST 725 for measuring insulation resistance of devices, Benning 050316 | Benning GmbH |
| DUSPOL_1000 | Tester DUSPOL 1000 for U=12-1000V LED, presence of curcuit, phase sequence, IP64, IEC/EN 61243-3,Benning 050260 | Benning GmbH |
| DUSPOL_ANALOG_N | Tester DUSPOL analog new for U=12-1000V LED Is=600mA,1000V, solenoid, phase consecuence, IP65, IEC/EN 61243-3, Benning 050261 | Benning GmbH |
| DUSPOL_ANALOGPLUS | Tester DUSPOL analog plus for U=12-690V LED, phase sequence IP64, IEC/EN 61243-3, Benning 050257 | Benning GmbH |
| DUSPOL_COMBI | Tester DUSPOL combi for U=12-750V LED, Continuity test, vibrating alarm, IP64, IEC/EN 61243-3, Benning 050254 | Benning GmbH |
| DUSPOL_COMPACT | Tester DUSPOL compact for U=12-750V LED, IP64, IEC/EN 61243-3, Benning 050251 | Benning GmbH |
| DUSPOL_DIGITAL_C | Tester DUSPOL digital (new) with case 1 – 1000 V AC, 1 – 1200 V DC, LCD / LED, Is=550 mA, 0.1 kΩ – 300 kΩ, 1 Hz – 1000 Hz, diode test, continuity, non-contact detector, vibration, IP65, Benning 050264 | Benning GmbH |
| DUSPOL_DIGITAL_N | Tester DUSPOL digital new for U=1-1000V AC/1200DC, LCD, Is=550mA,1000V, continuity test, phase sequence, vibrating alarm, IP65, IEC/EN 61243-3, Benning 050263 | Benning GmbH |
| DUSPOL_DIGITALLC | Tester DUSPOL digital LC for U=6-750V LCD, 200mA, 200kOmh, continuity test, phase sequence, vibrating alarm, IP64, IEC/EN 61243-3, Benning 050258 | Benning GmbH |
| DUSPOL_EXPERT | Tester DUSPOL expert for U=12-750V LED, continuity test, phase sequence, vibrating alarm, IP64, IEC/EN 61243-3, Benning 050253 | Benning GmbH |
| DUSPOL_EXPERT_N | Tester DUSPOL expert new for U=12-1000V LED, sound signal, Is=550mA,1000V, continuity test, phase sequence, IP65, IEC/EN 61243-3,Benning 050262 | Benning GmbH |
| DUTEST | Tester DUTEST continuity test 0-900 Ohm, 0-90 KOhm, Benning 050155 | Benning GmbH |
| DUTEST_PRO | Tester DUTEST pro, 6-400 V AC/DC, LED, continuity, buzzer, 0 - 100 ohm/1 kOhm/10 kOhm (yellow LEDs), polarity test, Benning 050156 | Benning GmbH |
| PRO_BAG | Protective bag for testers and measuring devices, Benning 711019 | Benning GmbH |
| TE_006_400_B155 | Tester PROFIPOL for U=6-400V, IP65, Benning 020022 | Benning GmbH |
| TRITEST_CONTROL | Tester TRITEST control for U=400-600V LED50-60Hz 3-phase secuence test, IP30, IEC/EN 61010-031,Benning 020050 | Benning GmbH |
| TRITEST_PRO | Tester TRITEST Pro, 400-500 V AC, LED, phase sequence, CAT III 300 V, IEC/EN 61010-1, Benning 020052 | Benning GmbH |
| CASE_ZAP_350 | Leadher cover for tester ZAP 350 for testing of KWH-meters, Tietzsch | |
| TE_ZAP_350 | Tester ZAP 350 for KWh-meters checking, Tietzsch | |
| TE4_PH_220_380 | Phase secuence tester 220-380 V ~ ТЕ-4 |
